Latest: Reading an Epoxy Flooring Quote: Mils, Solids and the Words That Matter

Chrisharrispresents

Metallic and flake epoxy floors for Allen garages, shops, and living spaces.

Reading an Epoxy Flooring Quote: Mils, Solids and the Words That Matter

Bright modern underground parking structure with vivid directional arrows

Two written quotes for the same garage slab can describe floors that will not last the same number of years, and the difference almost never shows up in the summary line. It shows up further down, in the words most people skip: mils, solids, broadcast rate, topcoat, cure schedule. Those words are the specification. The rest of the page is sales copy.

Learning six or seven of those terms buys something more useful than a lower figure. It buys the ability to tell whether two bids are even describing the same product. One may be a single thin roll-on coat over a lightly etched floor. The other may be a mechanically ground slab, a high solids base coat, a full flake broadcast and a separate wear coat on top. Both get called epoxy on the invoice. Only one of them is a floor you stop thinking about.

Around Allen, the vocabulary below is the same vocabulary that epoxy flooring teams in allen use among themselves when they scope a job, and once it is familiar, a quote stops being a number and starts being a description of work.

Mils, and why the thickness number outranks the brand

A mil is one thousandth of an inch. Coating thickness is measured in mils, and it is the single number that predicts most of what the floor will do over time: how it handles a dropped socket wrench, whether hot tires lift it, how long the gloss survives grit tracked in from the driveway.

Here is the part that confuses people. A quote may list a total system thickness, or it may list each layer, or it may list the wet film thickness, which is how thick the material sits before the solvent or water leaves it. Wet and dry are different numbers, and the dry number is the one you own. A coating rolled out at eight wet mils with half its volume made of carrier dries to something closer to four. A high solids product rolled at the same wet thickness keeps almost all of it.

So the question to ask is simple and it should not be met with hesitation: what is the dry film thickness of the finished system, measured from the slab to the top of the wear coat? A thin system is not automatically wrong. A thin system sold as equivalent to a thick one is.

Solids content, stated as a number or dodged entirely

Solids content is the share of the can that stays on the floor. Everything else evaporates. A nearly all solids resin leaves behind almost the whole bucket. A water thinned product leaves behind a fraction, which is why its coverage per container looks so generous on paper.

This is where coverage rates mislead. Square feet per unit is a function of solids, not of quality, and spreading one unit further is not efficiency. It is a thinner floor. When a bid boasts about how far the material goes, read it as a statement about thickness and price it accordingly.

What a roller can actually carry

There is also a physical ceiling. A roller can only lay down so much material in one pass before it sags, forms roll marks or traps air, which is why thick systems are built in layers rather than in one heavy coat. A quote promising a substantial finished thickness in a single application is describing something that does not happen on a flat slab.

The base coat and the topcoat are different chemistries

Epoxy is a good base and a mediocre surface. It bonds hard to concrete and it fills, but left exposed it chalks and ambers under ultraviolet light, which matters a great deal on a garage floor that spends hours a day with the door up and North Texas sun crossing the first several feet of it.

That is why most durable systems finish with something else on top, commonly a polyaspartic or a urethane. Those cure faster, hold gloss in sunlight and resist the chemicals a garage sees. A quote that lists only epoxy, with no named wear coat, is describing a floor whose outer surface is the part most likely to fade.

The follow-up question is worth asking plainly: what is the final coat, and is it rated for ultraviolet exposure? Two coats of the same epoxy is a thicker epoxy floor, not a protected one.

Flake is sold by coverage, not by color

Decorative flake, the vinyl chip that gives most garage floors their speckled look, is specified by how heavily it is broadcast. A light scatter leaves resin showing between the chips. A full broadcast means flake is thrown until the surface will take no more, then the excess is swept back up the next morning before the clear coat goes down.

The difference is visible and functional. A full broadcast builds texture, which is traction, and it hides the slab's own imperfections and future scuffs. A light scatter shows every roller line and every repair underneath. Flake also adds real thickness once it is locked in, so broadcast density and system thickness are related answers, not separate ones.

Ask which it is. Ask whether the excess is reclaimed and whether the surface is scraped flat before the clear goes on, because unscraped flake edges stand up and feel like sandpaper underfoot.

Preparation is a line item, and it should have its own paragraph

Nothing in a coating system matters if the bond fails, and the bond is made during preparation. Diamond grinding opens the surface of the concrete mechanically and leaves a uniform profile the resin can key into. Acid etching is cheaper, faster, less consistent, and it struggles badly on a slab that has been sealed or has absorbed years of oil.

A quote should say which method it uses, and it should say what happens to cracks, control joints, pitting and spalled edges. Those are separate operations with separate materials. A bid that mentions preparation only as a single word is leaving the most failure prone step undefined, which conveniently also leaves it adjustable later.

Oil is its own line. Deep contamination needs degreasing and sometimes grinding past the stained layer, and no coating bonds through it.

Moisture, which the slab decides and the calendar does not

Many homes across Allen sit on slab on grade over expansive clay, and water moves up through concrete as vapor whether anyone tested for it or not. Vapor pressure under a sealed coating is one of the standard reasons a floor lets go in sheets months after it looked perfect.

The test is cheap and it is not optional on a slab with unknown history. A calcium chloride test or a relative humidity probe gives a number, and that number determines whether a vapor tolerant primer belongs in the system. If no moisture test appears anywhere in the scope, the quote has priced an assumption.

Cure schedule: what you are really buying is time

Two numbers matter after the crew leaves, and they are not the same. Foot traffic cure is when you can walk on it. Full chemical and vehicle cure is when tires can sit on it without printing the surface, and it is usually days later, longer when the garage is hot and still.

Summer here works against the calendar twice over. High slab temperatures shorten pot life, so material has to be mixed in smaller batches and moved quickly, while humidity can blush a topcoat that was rushed. A crew that gives you one vague number for cure, or promises cars back in that evening on an epoxy base, is managing your expectations rather than the chemistry.

Get it in writing: when can we walk on it, when can we park, and what happens if the weather that week pushes those dates.

Warranty language, read from the exclusions upward

Read the exclusions first. They describe the product more honestly than the headline term does. A long warranty that excludes delamination from moisture, hot tire pickup, ultraviolet discoloration and anything involving the slab itself has excluded the four things that actually go wrong.

Then look at what the remedy is. Repair of the affected area is a different promise from recoating the floor, and both are different from material replacement only, which means the manufacturer sends resin and the labor is yours. Ask who honors it, the installer or the manufacturer, and ask what voids it, because aggressive cleaners and parking a leaking vehicle often do.

The short list that makes two quotes comparable

Hand the same questions to everyone bidding, and the answers line the bids up next to each other:

  • What is the dry film thickness of the finished system, layer by layer?
  • What is the solids content of the base coat?
  • How is the slab prepared, and what is done with cracks, joints and oil?
  • Was a moisture test performed, and what did it read?
  • What is the final coat, and is it rated for sun exposure?
  • Is the flake a full broadcast, reclaimed and scraped before clear coat?
  • When can we walk on it, and when can we park on it?
  • What does the warranty exclude, and who honors it?

A contractor who answers all eight without reaching for a brochure is describing work they have done many times. A contractor who treats the questions as suspicion is telling you something too.

None of this requires becoming an expert in resin chemistry. It requires refusing to compare two unlike things because they share a word. Collin County garages take heat, grit, clay movement and a great deal of direct sun, and a floor specified honestly for those conditions outlives a cheaper one by enough years that the arithmetic stops being close.

Top